1. Tech

Your suggestion is on its way!

An email with a link to:

http://linux.about.com/library/cmd/blcmdl4_wavelan_cs.htm

was emailed to:

Thanks for sharing About.com with others!

Linux / Unix Command: wavelan_cs
Command Library

NAME

wavelan_cs - AT&T GIS WaveLAN PCMCIA device driver  

SYNOPSIS

insmod wavelan_cs.o [irq_list=i,j,...] [mem_speed=n] [do_roaming=n]  

DESCRIPTION

wavelan_cs is the low-level Card Services driver for the NCR / AT&T / Lucent WaveLAN PCMCIA and Digital (DEC) RoamAbout DS wireless ethernet adapter. When this driver is attached to a card, it allocates the next available ethernet device (eth0..eth#). This device name will be passed on to cardmgr(8) for the card configuration, and reported in the kernel log file with the MAC address, NWID and frequency used by the card.  

PARAMETERS

irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
mem_speed=n
Sets the access speed of the shared memory window, in nanoseconds. The default is 0 (i.e., no extra wait states).
do_roaming=n
Enables or disables roaming mode. The default is 1 (roam).
 

WIRELESS EXTENSIONS

Use iwconfig(8) to manipulate wireless extensions.  

Mode

Set the operating mode to Ad-Hoc or Managed. This in fact disable or enable roaming support. This setting is not saved in hardware.  

Network ID

Set the network ID [0 to FFFF] or disable it [off] or reenable it [on]. As the NWID is stored in the card Permanent Storage Area, it will be reuse at any further invocation of the driver.  

Frequency & channels

For the 2.4GHz 2.00 Hardware, you are able to set the frequency by specifying one of the 10 defined channels (2.412, 2.422, 2.425, 2.4305, 2.432, 2.442, 2.452, 2.460, 2.462 or 2.484) or directly by its value. The frequency is changed immediately and permanentely. Frequency availability depend on the regulations...  

Sensitivity

Signal level threshold for packet reception [0 to 63]. Should be set according to the ambiant noise level.  

Encryption key

Set the encryption key [0 to FFFF-FFFF-FFFF-FFFF]. Use [off] and [on] to disable and reenable the hardware encryption. This feature works only for device with encryption option (DES or AES).  

Statistics spy

Set a list of MAC addresses in the driver (up to 8) and get the last quality of link for each of those (see iwspy(8)).  

/proc/net/wireless

status is the status reported by the modem. Link quality reports the quality of the modulation on the air (direct sequence spread spectrum) [max = 16]. Level and Noise refer to the signal level and noise level [max = 64]. The crypt discarded packet and misc discarded packet counters are not implemented.  

PRIVATE IOCTL

You may use iwpriv(8) to manipulate private ioctls.  

Quality threshold

Enable you the define the quality threshold used by the modem (packet below that level are discarded).  

Histogram

This functionality allow to set a number of signal level intervals and to count the number of packets received in each of those defined intervals. This distribution might be used to calculate the mean value and standard deviation of the signal level.  

OTHER FEATURES

Hot unplug support.
Power saving (use 'ifconfig down').  

SPECIFIC NOTES

This driver will fail to load some non NCR/ATT&T/Lucent Wavelan cards. If it's your case, you must look in the source code on how to add your card to the detection routine.

Some of the mentioned features are optional. You may enable to disable them by changing flags in the driver header and recompile.  

SEE ALSO

wavelan(4), cardmgr(8), pcmcia(5), ifconfig(8), insmod(1), iwconfig(8), iwspy(8), iwpriv(8).


Important: Use the man command (% man) to see how a command is used on your particular computer.

>> Linux/Unix Command Library

>> Shell Command Library

You can opt-out at any time. Please refer to our privacy policy for contact information.

Discuss in my forum

©2014 About.com. All rights reserved.