|Linux / Unix Command: mkfs.msdos|
NAMEmkdosfs - create an MS-DOS file system under Linux
SYNOPSISmkdosfs [ -A ] [ -b sector-of-backup ] [ -c ] [ -l filename ] [ -C ] [ -f number-of-FATs ] [ -F FAT-size ] [ -i volume-id ] [ -I ] [ -m message-file ] [ -n volume-name ] [ -r root-dir-entries ] [ -R number-of-reserved-sectors ] [ -s sectors-per-cluster ] [ -S logical-sector-size ] [ -v ] device [ block-count ]
DESCRIPTIONmkdosfs is used to create an MS-DOS file system under Linux on a device (usually a disk partition). device is the special file corresponding to the device (e.g /dev/hdXX). block-count is the number of blocks on the device. If omitted, mkdosfs automatically determiness the file system size.
- Use Atari variation of the MS-DOS filesystem. This is default if mkdosfs is run on an Atari, then this option turns off Atari format. There are some differences when using Atari format: If not directed otherwise by the user, mkdosfs will always use 2 sectors per cluster, since GEMDOS doesn't like other values very much. It will also obey the maximum number of sectors GEMDOS can handle. Larger filesystems are managed by raising the logical sector size. Under Atari format, an Atari-compatible serial number for the filesystem is generated, and a 12 bit FAT is used only for filesystems that have one of the usual floppy sizes (720k, 1.2M, 1.44M, 2.88M), a 16 bit FAT otherwise. This can be overridden with the -F option. Some PC-specific boot sector fields aren't written, and a boot message (option -m) is ignored.
- -b sector-of-backup
- Selects the location of the backup boot sector for FAT32. Default depends on number of reserved sectors, but usually is sector 6. The backup must be within the range of reserved sectors.
- Check the device for bad blocks before creating the file system.
- Create the file given as device on the command line, and write the to-be-created file system to it. This can be used to create the new file system in a file instead of on a real device, and to avoid using dd in advance to create a file of appropriate size. With this option, the block-count must be given, because otherwise the intended size of the file system wouldn't be known. The file created is a sparse file, which actually only contains the meta-data areas (boot sector, FATs, and root directory). The data portions won't be stored on the disk, but the file nevertheless will have the correct size. The resulting file can be copied later to a floppy disk or other device, or mounted through a loop device.
- -f number-of-FATs
- Specify the number of file allocation tables in the file system. The default is 2. Currently the Linux MS-DOS file system does not support more than 2 FATs.
- -F FAT-size
- Specifies the type of file allocation tables used (12, 16 or 32 bit). If nothing is specified, mkdosfs will automatically select between 12 and 16 bit, whatever fits better for the filesystem size. 32 bit FAT (FAT32 format) must (still) be selected explicitly if you want it.
- -i volume-id
- Sets the volume ID of the newly created filesystem; volume-id is a 32-bit hexadecimal number (for example, 2e24ec82). The default is a number which depends on the filesystem creation time.
Normally you are not allowed to use any 'full' fixed disk devices.
will complain and tell you that it refuses to work. This is different
when usind MO disks. One doesn't always need partitions on MO disks.
The filesytem can go directly to the whole disk. Under other OSes
this is known as the 'superfloppy' format.
This switch will force mkdosfs to work properly.
- -l filename
- Read the bad blocks list from filename.
- -m message-file
- Sets the message the user receives on attempts to boot this filesystem without having properly installed an operating system. The message file must not exceed 418 bytes once line feeds have been converted to carriage return-line feed combinations, and tabs have been expanded. If the filename is a hyphen (-), the text is taken from standard input.
- -n volume-name
- Sets the volume name (label) of the filesystem. The volume name can be up to 11 characters long. The default is no label.
- -r root-dir-entries
- Select the number of entries available in the root directory. The default is 112 or 224 for floppies and 512 for hard disks.
- -R number-of-reserved-sectors
- Select the number of reserved sectos. With FAT32 format at least 2 reserved sectors are needed, the default is 32. Otherwise the default is 1 (only the boot sector).
- -s sectors-per-cluster
- Specify the number of disk sectors per cluster. Must be a power of 2, i.e. 1, 2, 4, 8, ... 128.
- -S logical-sector-size
- Specify the number of bytes per logical sector. Must be a power of 2 and greater than or equal to 512, i.e. 512, 1024, 2048, 4096, 8192, 16384, or 32768.
- Verbose execution.
SEE ALSOdosfsck(8), mkfs(8)
Important: Use the man command (% man) to see how a command is used on your particular computer.